43 lines
2.3 KiB
Markdown
43 lines
2.3 KiB
Markdown
|
# 3dfoxc
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
A [3d-printed whitefox](https://www.thingiverse.com/thing:2952008) with an Elite-C microcontroller.
|
||
|
|
|
||
|
|
This is a build of [matt3o's "How to Build a Custom Keyboard" guide](https://matt3o.com/book/), except that I have replaced the Teensy with an [Elite-C v4](https://keeb.io/products/elite-c-low-profile-version-usb-c-pro-micro-replacement-atmega32u4). Presumably you could replace it with anything compatible. The USB-C port had to be enlarged with dremel, and the mount for the Teensy was ground off and replaced with everyone's favorite rapid modeling polymer ... hot glue.
|
||
|
|
|
||
|
|
* Keyboard Maintainer: [david l goodrich](mailto:dlg@dsrw.org)
|
||
|
|
* Hardware Supported:
|
||
|
|
* [3d-printed whitefox](https://www.thingiverse.com/thing:2952008)
|
||
|
|
* Elite-C microcontroller
|
||
|
|
* Hardware Availability: [keebio](https://keeb.io/products/elite-c-low-profile-version-usb-c-pro-micro-replacement-atmega32u4), [1up](https://1upkeyboards.com/shop/controllers/elite-c-v4-controller/), [keyhive](https://keyhive.xyz/shop/elite-c), [splitkb](https://splitkb.com/products/elite-c-low-profile-rev4-microcontroller)
|
||
|
|
|
||
|
|
## Wiring
|
||
|
|
|
||
|
|
Badly, because I have never done this before. Build pics available upon request, I guess.
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## Flashing
|
||
|
|
|
||
|
|
Make example for this keyboard (after setting up your build environment):
|
||
|
|
|
||
|
|
make handwired/3dfoxc:default
|
||
|
|
|
||
|
|
Flashing example for this keyboard (use the `dfu` target for the Elite-C!):
|
||
|
|
|
||
|
|
make handwired/3dfoxc:default:dfu
|
||
|
|
|
||
|
|
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|
||
|
|
|
||
|
|
## Bootloader
|
||
|
|
|
||
|
|
Enter the bootloader in 3 ways:
|
||
|
|
|
||
|
|
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (usually the top left key or Escape) and plug in the keyboard
|
||
|
|
* **Physical reset button**: Briefly press the button on the back of the PCB - some may have pads you must short instead
|
||
|
|
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
|
||
|
|
|
||
|
|
|