From 5dd698638545fe4b065d42a6b0c4622352c3b7cc Mon Sep 17 00:00:00 2001 From: Voron Trident 350 Date: Sun, 2 Nov 2025 20:26:49 +0000 Subject: [PATCH] New backup from 02/11/25 - 20:26:49 --- printer_data/config | 1 - printer_data/config/README.md | 7 + printer_data/config/crowsnest.conf | 45 +++ printer_data/config/moonraker.conf | 46 +++ printer_data/config/nitehawk-36.cfg | 129 +++++++ printer_data/config/nitehawk-sb.cfg | 150 ++++++++ printer_data/config/printer.cfg | 550 +++++++++++++++++++++++++++ printer_data/config/printer.cfg.dist | 11 + 8 files changed, 938 insertions(+), 1 deletion(-) delete mode 160000 printer_data/config create mode 100644 printer_data/config/README.md create mode 100644 printer_data/config/crowsnest.conf create mode 100644 printer_data/config/moonraker.conf create mode 100644 printer_data/config/nitehawk-36.cfg create mode 100644 printer_data/config/nitehawk-sb.cfg create mode 100644 printer_data/config/printer.cfg create mode 100644 printer_data/config/printer.cfg.dist diff --git a/printer_data/config b/printer_data/config deleted file mode 160000 index a5803f3..0000000 --- a/printer_data/config +++ /dev/null @@ -1 +0,0 @@ -Subproject commit a5803f34b319d594f3c6696bebdbe22a1a442aed diff --git a/printer_data/config/README.md b/printer_data/config/README.md new file mode 100644 index 0000000..ab5e229 --- /dev/null +++ b/printer_data/config/README.md @@ -0,0 +1,7 @@ +# Voron Trident 350 + +Hardware: +* Raspberry Pi 3B +* BigTreeTech Octopus +* LDO Nighthawk 36 +* Nevermore diff --git a/printer_data/config/crowsnest.conf b/printer_data/config/crowsnest.conf new file mode 100644 index 0000000..86936a3 --- /dev/null +++ b/printer_data/config/crowsnest.conf @@ -0,0 +1,45 @@ +#### crowsnest.conf +#### This is the default config after installation. +#### It is also used as the default config in MainsailOS. +#### For details on how to configure this to your needs, see: +#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md + + +##################################################################### +#### ##### +#### Information about ports and according URL's ##### +#### ##### +##################################################################### +#### ##### +#### Port 8080 equals /webcam/?action=[stream/snapshot] ##### +#### Port 8081 equals /webcam2/?action=[stream/snapshot] ##### +#### Port 8082 equals /webcam3/?action=[stream/snapshot] ##### +#### Port 8083 equals /webcam4/?action=[stream/snapshot] ##### +#### ##### +#### Note: These ports are default for most Mainsail ##### +#### installations. Using any other port would involve ##### +#### changing the proxy configuration or using URLs ##### +#### with the specific port like ##### +#### http://:/?action=[stream/snapshot] ##### +#### ##### +##################################################################### +#### RTSP Stream URL: ( if enabled and supported ) ##### +#### rtsp://:/stream.h264 ##### +##################################################################### + + +[crowsnest] +log_path: /home/printer/printer_data/logs/crowsnest.log +log_level: verbose # Valid Options are quiet/verbose/debug +delete_log: false # Deletes log on every restart, if set to true +no_proxy: false # If set to true, no reverse proxy is required. Only change this, if you know what you are doing. + +[cam 1] +mode: ustreamer # ustreamer - Provides MJPG and snapshots. (All devices) + # camera-streamer - Provides WebRTC, MJPG and snapshots. (only RPiOS + RPi 0/1/2/3/4) +port: 8080 # HTTP/MJPG stream/snapshot port +device: /dev/video0 # See log for available devices +resolution: 640x480 # x format +max_fps: 15 # If hardware supports it, it will be forced, otherwise ignored/coerced. +#custom_flags: # You can run the stream services with custom flags. +#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see log for your camera capabilities. diff --git a/printer_data/config/moonraker.conf b/printer_data/config/moonraker.conf new file mode 100644 index 0000000..e8e73a4 --- /dev/null +++ b/printer_data/config/moonraker.conf @@ -0,0 +1,46 @@ +[server] +host: 0.0.0.0 +port: 7125 +klippy_uds_address: /home/printer/printer_data/comms/klippy.sock + +[authorization] +trusted_clients: + 10.42.0.0/16 + 10.0.0.0/8 + 127.0.0.0/8 + 169.254.0.0/16 + 172.16.0.0/12 + 192.168.0.0/16 + FC00::/7 + FE80::/10 + ::1/128 +cors_domains: + *.lan + *.local + *://localhost + *://localhost:* + *://my.mainsail.xyz + *://app.fluidd.xyz + +[octoprint_compat] + +[history] + +[update_manager] +channel: dev +refresh_interval: 168 + +[update_manager mainsail] +path: /home/printer/mainsail +repo: mainsail-crew/mainsail +channel: stable +type: web +persistent_files: + config.json + +[update_manager mainsail-config] +managed_services: klipper +origin: https://github.com/mainsail-crew/mainsail-config.git +path: /home/printer/mainsail-config +primary_branch: master +type: git_repo diff --git a/printer_data/config/nitehawk-36.cfg b/printer_data/config/nitehawk-36.cfg new file mode 100644 index 0000000..725738e --- /dev/null +++ b/printer_data/config/nitehawk-36.cfg @@ -0,0 +1,129 @@ +# This file contains pin mappings for the LDO Nitehawk-36 Toolboard +# To use this config, the firmware should be compiled for the Raspberry Pi RP2040 +# Make sure to include this config *at the end* of printer.cfg to overwrite the relevent sections + +# See https://docs.ldomotors.com/en/Toolboard/nitehawk-36#firmware-setup-and-update +# For instructions on uploading/updating klipper firmware to the PCB + +## LDO Nitehawk-SB Toolboard Partial Config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] sections + +## *MAKE SURE* to include this partial config file *AFTER* the main controller config. +## This will ensure the relavent sections are overwritten by the pin mappings specified here. + +[mcu nhk] +## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_rp2040_4E363334320E22C6-if00 +restart_method: command +##-------------------------------------------------------------------- + +##################################################################### +# Endstops +##################################################################### +## XES - Toolhead PCB +[stepper_x] +endstop_pin: nhk:gpio13 + + +##################################################################### +# Filament Sensor +##################################################################### +#[filament_switch_sensor filament_sensor] +#switch_pin: nhk:gpio3 +#pause_on_runout: True + +##################################################################### +# Extruder +##################################################################### +[extruder] +step_pin: nhk:gpio23 +dir_pin: nhk:gpio24 +enable_pin: !nhk:gpio25 +heater_pin: nhk:gpio9 +sensor_pin: nhk:gpio29 +pullup_resistor: 2200 + +[tmc2209 extruder] +sense_resistor: 0.100 +uart_pin: nhk:gpio0 +tx_pin: nhk:gpio1 +interpolate: false +#run_current: #recommend setting it below 0.7A. + +##################################################################### +# Fans +##################################################################### +## PCF +[fan] +pin: nhk:gpio6 + + +## HEF +[heater_fan hotend_fan] +pin: nhk:gpio5 +tachometer_pin: nhk:gpio16 +tachometer_ppr: 2 + +##################################################################### +# Probe +##################################################################### +## Probe Port +[probe] +pin: nhk:gpio10 + +##################################################################### +# Lights +##################################################################### +##Stealthburner Headlights +[neopixel sb_leds] +pin: nhk:gpio7 +chain_count: 3 +color_order: GRBW +initial_RED: 0.0 +initial_GREEN: 0.0 +initial_BLUE: 1.0 +initial_WHITE: 0.0 + +## PCB Activity Light +[output_pin act_led] +pin: !nhk:gpio8 + +##################################################################### +# Accelerometer +##################################################################### +[adxl345] +cs_pin: nhk:gpio27 +spi_software_sclk_pin: nhk:gpio18 +spi_software_mosi_pin: nhk:gpio20 +spi_software_miso_pin: nhk:gpio19 + +[resonance_tester] +accel_chip: adxl345 +accel_per_hz: 100 +sweeping_accel: 400 +sweeping_period: 0 +##-------------------------------------------------------------------- +## Uncomment below for 250mm build +#probe_points: +# 125, 125, 20 + +## Uncomment below for 300mm build +#probe_points: +# 155, 155, 20 + +## Uncomment below for 350mm build +#probe_points: +# 175, 175, 20 + +##################################################################### +# Addtional Sensors +##################################################################### +[temperature_sensor NH36] +sensor_type: temperature_mcu +sensor_mcu: nhk +min_temp: 0 +max_temp: 100 diff --git a/printer_data/config/nitehawk-sb.cfg b/printer_data/config/nitehawk-sb.cfg new file mode 100644 index 0000000..83c93ad --- /dev/null +++ b/printer_data/config/nitehawk-sb.cfg @@ -0,0 +1,150 @@ +# This file contains pin mappings for the LDO Nitehawk-SB Toolboard +# To use this config, the firmware should be compiled for the Raspberry Pi RP2040 +# Make sure to include this config *at the end* of printer.cfg to overwrite the relevent sections + +# See https://docs.ldomotors.com/en/voron/nitehawk-sb#firmware-setup-and-update +# For instructions on uploading/updating klipper firmware to the PCB + +## LDO Nitehawk-SB Toolboard Partial Config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] sections + +## *MAKE SURE* to include this partial config file *AFTER* the main controller config. +## This will ensure the relavent sections are overwritten by the pin mappings specified here. + +[mcu nhk] +## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_rp2040_4E363334320E22C6-if00 +restart_method: command +##-------------------------------------------------------------------- + +##################################################################### +# Endstops +##################################################################### + +## XES - Toolhead PCB +[stepper_x] +endstop_pin: nhk:gpio13 + +## YES - Toolhead PCB +[stepper_y] +endstop_pin: nhk:gpio12 + +##################################################################### +# Extruder +##################################################################### +[extruder] +step_pin: nhk:gpio23 +dir_pin: nhk:gpio24 +enable_pin: !nhk:gpio25 +heater_pin: nhk:gpio9 +sensor_pin: nhk:gpio29 +pullup_resistor: 2200 + +[tmc2209 extruder] +sense_resistor: 0.100 +uart_pin: nhk:gpio0 +tx_pin: nhk:gpio1 +interpolate: false +#run_current: #recommend setting it below 0.7A. + + +##################################################################### +# Fans +##################################################################### +## PCF +[fan] +pin: nhk:gpio6 +#tachometer_pin: nhk:gpio17 +#tachometer_ppr: 2 + +## HEF +[heater_fan hotend_fan] +pin: nhk:gpio5 +tachometer_pin: nhk:gpio16 +tachometer_ppr: 2 + +##################################################################### +# Probe +##################################################################### +## Probe Port +#[probe] +#pin: nhk:gpio10 + +##################################################################### +# Lights +##################################################################### +##Stealthburner Headlights +[neopixel sb_leds] +pin: nhk:gpio7 +chain_count: 3 +color_order: GRBW +initial_RED: 0.0 +initial_GREEN: 0.0 +initial_BLUE: 1.0 +initial_WHITE: 0.0 + +## PCB Activity Light +[output_pin act_led] +pin: !nhk:gpio8 + +##################################################################### +# Accelerometer +##################################################################### +[adxl345] +cs_pin: nhk:gpio21 +spi_software_sclk_pin: nhk:gpio18 +spi_software_mosi_pin: nhk:gpio20 +spi_software_miso_pin: nhk:gpio19 + +[resonance_tester] +accel_chip: adxl345 +accel_per_hz: 100 +sweeping_accel: 400 +sweeping_period: 0 +##-------------------------------------------------------------------- +## Uncomment below for 250mm build +#probe_points: +# 125, 125, 20 + +## Uncomment below for 300mm build +#probe_points: +# 155, 155, 20 + +## Uncomment below for 350mm build +#probe_points: +# 175, 175, 20 + +##-------------------------------------------------------------------- + +##################################################################### +# Thermistors +# ##################################################################### +## External Chamber Thermistor Port +[temperature_sensor chamber_temp] +sensor_type: Generic 3950 +sensor_pin: nhk:gpio28 +min_temp: 0 +max_temp: 100 +gcode_id: chamber_th + +[thermistor CMFB103F3950FANT] +temperature1: 0.0 +resistance1: 32116.0 +temperature2: 40.0 +resistance2: 5309.0 +temperature3: 80.0 +resistance3: 1228.0 + +[temperature_sensor nh_temp] +## Nitehawk PCB Sensor +sensor_type: CMFB103F3950FANT +sensor_pin: nhk:gpio26 +pullup_resistor: 2200 +min_temp: 0 +max_temp: 100 +gcode_id: nh_th + diff --git a/printer_data/config/printer.cfg b/printer_data/config/printer.cfg new file mode 100644 index 0000000..53d5b4d --- /dev/null +++ b/printer_data/config/printer.cfg @@ -0,0 +1,550 @@ +[include mainsail.cfg] +# This file contains common pin mappings for the BigTreeTech Octopus V1. +# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader" +# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference + +# after running "make", copy the generated "klipper/out/klipper.bin" file to a +# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card. + +# See docs/Config_Reference.md for a description of parameters. + +## Voron Design Trident 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types +## Hotend heater pin [extruder] section +## Leadscrew Rotation Distance [stepper_z], [stepper_z1], [stepper_z2] +## Z Endstop Switch location [safe_z_home] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Stepper Z1 enable pin [stepper_z1] section +## PID tune [extruder] and [heater_bed] sections +## Probe pin [probe] section +## Fine tune E steps [extruder] section + +[mcu] +## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_370048001150535556323420-if00 +restart_method: command +##-------------------------------------------------------------------- + +[include nighthawk-36.cfg] + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +## B Stepper - Left +## Connected to MOTOR_0 +## Endstop connected to DIAG_0 +[stepper_x] +step_pin: PF13 +dir_pin: !PF12 +enable_pin: !PF14 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: PG6 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +position_endstop: 350 +position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_x] +uart_pin: PC4 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## A Stepper - Right +## Connected to MOTOR_1 +## Endstop connected to DIAG_1 +[stepper_y] +step_pin: PG0 +dir_pin: !PG1 +enable_pin: !PF15 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: PG9 +position_min: 0 +##-------------------------------------------------------------------- + +## Uncomment for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +#position_endstop: 300 +#position_max: 300 + +## Uncomment for 350mm build +position_endstop: 350 +position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_y] +uart_pin: PD11 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Z Stepper Settings +##################################################################### + +## Z0 Stepper - Front Left +## Connected to MOTOR_2 +## Endstop connected to DIAG_2 +[stepper_z] +step_pin: PF11 +dir_pin: PG3 +enable_pin: !PG5 +# Rotation Distance for TR8x8 = 8, TR8x4 = 4, TR8x2 = 2 +rotation_distance: 8 +microsteps: 32 +endstop_pin: PG10 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +position_endstop: -0.5 +## All builds use same Max Z +position_max: 250 +position_min: -2.5 +homing_speed: 8.0 # Leadscrews are slower than 2.4, 10 is a recommended max. +second_homing_speed: 3 +homing_retract_dist: 3 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z] +uart_pin: PC6 +interpolate: False +run_current: 0.6 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z1 Stepper - Rear Center +## Connected to MOTOR_3 +[stepper_z1] +step_pin: PG4 +dir_pin: PC1 +## Octopus 1.0 & 1.1. Octopus PRO 1.0 +enable_pin: !PA0 +## Octopus PRO 1.1 +#enable_pin: !PA2 +# Rotation Distance for TR8x8 = 8, TR8x4 = 4, TR8x2 = 2 +rotation_distance: 8 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z1] +uart_pin: PC7 +interpolate: False +run_current: 0.6 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## Z2 Stepper - Front Right +## Connected to MOTOR_4 +[stepper_z2] +step_pin: PF9 +dir_pin: PF10 +enable_pin: !PG2 +# Rotation Distance for TR8x8 = 8, TR8x4 = 4, TR8x2 = 2 +rotation_distance: 8 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z2] +uart_pin: PF2 +interpolate: False +run_current: 0.6 +sense_resistor: 0.110 +stealthchop_threshold: 0 + + +##################################################################### +# Extruder +##################################################################### + +# Connected to MOTOR_6 +# Heater - HE0 +# Thermistor - T0 +#[extruder] +#step_pin: PE2 +#dir_pin: PE3 +#enable_pin: !PD4 +### Update value below when you perform extruder calibration +### If you ask for 100mm of filament, but in reality it is 98mm: +### rotation_distance = * / 100 +### 22.6789511 is a good starting point +#rotation_distance: 22.6789511 #Bondtech 5mm Drive Gears +### Update Gear Ratio depending on your Extruder Type +### Use 50:10 for Stealthburner/Clockwork 2 +### Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +### Use 80:20 for M4, M3.1 +#gear_ratio: 50:10 +#microsteps: 32 +#full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +#nozzle_diameter: 0.400 +#filament_diameter: 1.75 +### Octopus 1.0 & 1.1. Octopus PRO 1.0 +##heater_pin: PA2 +### Octopus PRO 1.1 +##heater_pin: PA0 +### Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. +### Use "Generic 3950" for NTC 100k 3950 thermistors +##sensor_type: +#sensor_pin: PF4 +#min_temp: 10 +#max_temp: 270 +#max_power: 1.0 +#min_extrude_temp: 170 +#control = pid +#pid_kp = 26.213 +#pid_ki = 1.304 +#pid_kd = 131.721 +### Try to keep pressure_advance below 1.0 +##pressure_advance: 0.05 +### Default is 0.040, leave stock +##pressure_advance_smooth_time: 0.040 +# +### E0 on MOTOR6 +### Make sure to update below for your relevant driver (2208 or 2209) +#[tmc2209 extruder] +#uart_pin: PE1 +#interpolate: false +#run_current: 0.5 +#sense_resistor: 0.110 +#stealthchop_threshold: 0 + + +##################################################################### +# Bed Heater +##################################################################### + +[heater_bed] +## SSR Pin - HE1 +## Thermistor - TB +heater_pin: PA3 +## Check what thermistor type you have. See https://www.klipper3d.org/Config_Reference.html#common-thermistors for common thermistor types. +## Use "Generic 3950" for Keenovo heaters +sensor_type: Generic 3950 +sensor_pin: PF3 +## Adjust max_power so it doesn't exceed the SSR rating. The Omron G3NA-210B-DC5 SSR is rated at 4 amps without a heatsink. +## The formula is "4 / (Wattage_of_bed_heater / Mains_voltage) = max_power" +## If max_power is greater than 1.0, use 1.0 +max_power: 0.6 +min_temp: 0 +max_temp: 120 +control: pid +pid_kp: 58.437 +pid_ki: 2.347 +pid_kd: 363.769 + +##################################################################### +# Probe +##################################################################### + +#[probe] +### Inductive Probe +### This probe is not used for Z height, only Quad Gantry Leveling +# +## Select the probe port by type: +### For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V. +##pin: ~!PB7 +### For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO. +##pin: PG15 +### For Octopus Pro Probe port; NPN and PNP proximity switch types can be set by jumper +##pin: ~!PC5 +# +##-------------------------------------------------------------------- +# +#x_offset: 0 +#y_offset: 25.0 +#z_offset: 0 +#speed: 10.0 +#samples: 3 +#samples_result: median +#sample_retract_dist: 3.0 +#samples_tolerance: 0.006 +#samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +#[fan] +### Print Cooling Fan - FAN0 +#pin: PA8 +#kick_start_time: 0.5 +### Depending on your fan, you may need to increase this value +### if your fan will not start. Can change cycle_time (increase) +### if your fan is not able to slow down effectively +#off_below: 0.10 + +#[heater_fan hotend_fan] +### Hotend Fan - FAN1 +#pin: PE5 +#max_power: 1.0 +#kick_start_time: 0.5 +#heater: extruder +#heater_temp: 50.0 +### If you are experiencing back flow, you can reduce fan_speed +##fan_speed: 1.0 + +[controller_fan controller_fan] +## Controller fan - FAN2 +pin: PD12 +kick_start_time: 0.5 +heater: heater_bed + +#[heater_fan exhaust_fan] +## Exhaust fan - FAN3 +#pin: PD13 +#max_power: 1.0 +#shutdown_speed: 0.0 +#kick_start_time: 5.0 +#heater: heater_bed +#heater_temp: 60 +#fan_speed: 1.0 + +##################################################################### +# LED Control +##################################################################### + +#[output_pin caselight] +# Chamber Lighting - HE2 Connector (Optional) +##Octopus 1.0 & 1.1, Octopus PRO 1.0 +#pin: PB10 +##Octopus PRO 1.1 +#pin: PB0 +#pwm:true +#shutdown_value: 0 +#value:1 +#cycle_time: 0.01 + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position:-10,-10 +speed:100 +z_hop:10 + +[z_tilt] +## Use Z_TILT_ADJUST to level the bed . +## z_positions: Location of toolhead + +##-------------------------------------------------------------------- +## Uncomment below for 250mm build +#z_positions: +# -50, 18 +# 125, 298 +# 300, 18 +#points: +# 30, 5 +# 125, 195 +# 220, 5 + +## Uncomment below for 300mm build +#z_positions: +# -50, 18 +# 150, 348 +# 350, 18 +#points: +# 30, 5 +# 150, 245 +# 270, 5 + +## Uncomment below for 350mm build +z_positions: + -50, 18 + 175, 398 + 400, 18 +points: + 30, 5 + 175, 295 + 320, 5 + + +##-------------------------------------------------------------------- + +speed: 200 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 + +######################################## +# EXP1 / EXP2 (display) pins +######################################## + +[board_pins] +aliases: + # EXP1 header + EXP1_1=PE8, EXP1_2=PE7, + EXP1_3=PE9, EXP1_4=PE10, + EXP1_5=PE12, EXP1_6=PE13, # Slot in the socket on this side + EXP1_7=PE14, EXP1_8=PE15, + EXP1_9=, EXP1_10=<5V>, + + # EXP2 header + EXP2_1=PA6, EXP2_2=PA5, + EXP2_3=PB1, EXP2_4=PA4, + EXP2_5=PB2, EXP2_6=PA7, # Slot in the socket on this side + EXP2_7=PC15, EXP2_8=, + EXP2_9=, EXP2_10=<5V> + +##################################################################### +# Displays +##################################################################### + +## Uncomment the display that you have +#-------------------------------------------------------------------- + +#[display] +## RepRapDiscount 128x64 Full Graphic Smart Controller +#lcd_type: st7920 +#cs_pin: EXP1_4 +#sclk_pin: EXP1_5 +#sid_pin: EXP1_3 +#menu_timeout: 40 +#encoder_pins: ^EXP2_5, ^EXP2_3 +#click_pin: ^!EXP1_2 + +#[output_pin beeper] +#pin: EXP1_1 + +#-------------------------------------------------------------------- + +#[display] +## mini12864 LCD Display +lcd_type: uc1701 +cs_pin: EXP1_3 +a0_pin: EXP1_4 +rst_pin: EXP1_5 +encoder_pins: ^EXP2_5, ^EXP2_3 +click_pin: ^!EXP1_2 +contrast: 63 +spi_software_miso_pin: EXP2_1 +spi_software_mosi_pin: EXP2_6 +spi_software_sclk_pin: EXP2_2 + +#[neopixel btt_mini12864] +## To control Neopixel RGB in mini12864 display +#pin: EXP1_6 +#chain_count: 3 +#initial_RED: 0.1 +#initial_GREEN: 0.5 +#initial_BLUE: 0.0 +#color_order: RGB + +## Set RGB values on boot up for each Neopixel. +## Index 1 = display, Index 2 and 3 = Knob +#[delayed_gcode setdisplayneopixel] +#initial_duration: 1 +#gcode: +# SET_LED LED=btt_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 +# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 +# SET_LED LED=btt_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 + +#-------------------------------------------------------------------- + + +##################################################################### +# Macros +##################################################################### + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - PLEASE CUSTOMISE THE SCRIPT +gcode: + M117 Homing... ; display message + G28 + Z_TILT_ADJUST + G28 + + ## Uncomment for for your size printer: + #-------------------------------------------------------------------- + ## Uncomment for 250mm build + #G0 X125 Y125 Z30 F3600 + + ## Uncomment for 300 build + #G0 X150 Y150 Z30 F3600 + + ## Uncomment for 350mm build + G0 X175 Y175 Z30 F3600 + #-------------------------------------------------------------------- + + + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + # safe anti-stringing move coords + {% set th = printer.toolhead %} + {% set x_safe = th.position.x + 20 * (1 if th.axis_maximum.x - th.position.x > 20 else -1) %} + {% set y_safe = th.position.y + 20 * (1 if th.axis_maximum.y - th.position.y > 20 else -1) %} + {% set z_safe = [th.position.z + 2, th.axis_maximum.z]|min %} + + SAVE_GCODE_STATE NAME=STATE_PRINT_END + + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-2.0 F3600 ; retract filament + + TURN_OFF_HEATERS + + G90 ; absolute positioning + G0 X{x_safe} Y{y_safe} Z{z_safe} F20000 ; move nozzle to remove stringing + G0 X{th.axis_maximum.x//2} Y{th.axis_maximum.y - 2} F3600 ; park nozzle at rear + M107 ; turn off fan + + BED_MESH_CLEAR + + # The purpose of the SAVE_GCODE_STATE/RESTORE_GCODE_STATE + # command pair is to restore the printer's coordinate system + # and speed settings since the commands above change them. + # However, to prevent any accidental, unintentional toolhead + # moves when restoring the state, explicitly set MOVE=0. + RESTORE_GCODE_STATE NAME=STATE_PRINT_END MOVE=0 diff --git a/printer_data/config/printer.cfg.dist b/printer_data/config/printer.cfg.dist new file mode 100644 index 0000000..b84e12c --- /dev/null +++ b/printer_data/config/printer.cfg.dist @@ -0,0 +1,11 @@ +[mcu] +serial: /dev/serial/by-id/ + +[virtual_sdcard] +path: /home/printer/printer_data/gcodes +on_error_gcode: CANCEL_PRINT + +[printer] +kinematics: none +max_velocity: 1000 +max_accel: 1000