151 lines
4.0 KiB
INI
151 lines
4.0 KiB
INI
# This file contains pin mappings for the LDO Nitehawk-SB Toolboard
|
|
# To use this config, the firmware should be compiled for the Raspberry Pi RP2040
|
|
# Make sure to include this config *at the end* of printer.cfg to overwrite the relevent sections
|
|
|
|
# See https://docs.ldomotors.com/en/voron/nitehawk-sb#firmware-setup-and-update
|
|
# For instructions on uploading/updating klipper firmware to the PCB
|
|
|
|
## LDO Nitehawk-SB Toolboard Partial Config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] sections
|
|
|
|
## *MAKE SURE* to include this partial config file *AFTER* the main controller config.
|
|
## This will ensure the relavent sections are overwritten by the pin mappings specified here.
|
|
|
|
[mcu nhk]
|
|
## Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_rp2040_4E363334320E22C6-if00
|
|
restart_method: command
|
|
##--------------------------------------------------------------------
|
|
|
|
#####################################################################
|
|
# Endstops
|
|
#####################################################################
|
|
|
|
## XES - Toolhead PCB
|
|
[stepper_x]
|
|
endstop_pin: nhk:gpio13
|
|
|
|
## YES - Toolhead PCB
|
|
[stepper_y]
|
|
endstop_pin: nhk:gpio12
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
[extruder]
|
|
step_pin: nhk:gpio23
|
|
dir_pin: nhk:gpio24
|
|
enable_pin: !nhk:gpio25
|
|
heater_pin: nhk:gpio9
|
|
sensor_pin: nhk:gpio29
|
|
pullup_resistor: 2200
|
|
|
|
[tmc2209 extruder]
|
|
sense_resistor: 0.100
|
|
uart_pin: nhk:gpio0
|
|
tx_pin: nhk:gpio1
|
|
interpolate: false
|
|
#run_current: #recommend setting it below 0.7A.
|
|
|
|
|
|
#####################################################################
|
|
# Fans
|
|
#####################################################################
|
|
## PCF
|
|
[fan]
|
|
pin: nhk:gpio6
|
|
#tachometer_pin: nhk:gpio17
|
|
#tachometer_ppr: 2
|
|
|
|
## HEF
|
|
[heater_fan hotend_fan]
|
|
pin: nhk:gpio5
|
|
tachometer_pin: nhk:gpio16
|
|
tachometer_ppr: 2
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
## Probe Port
|
|
#[probe]
|
|
#pin: nhk:gpio10
|
|
|
|
#####################################################################
|
|
# Lights
|
|
#####################################################################
|
|
##Stealthburner Headlights
|
|
[neopixel sb_leds]
|
|
pin: nhk:gpio7
|
|
chain_count: 3
|
|
color_order: GRBW
|
|
initial_RED: 0.0
|
|
initial_GREEN: 0.0
|
|
initial_BLUE: 1.0
|
|
initial_WHITE: 0.0
|
|
|
|
## PCB Activity Light
|
|
[output_pin act_led]
|
|
pin: !nhk:gpio8
|
|
|
|
#####################################################################
|
|
# Accelerometer
|
|
#####################################################################
|
|
[adxl345]
|
|
cs_pin: nhk:gpio21
|
|
spi_software_sclk_pin: nhk:gpio18
|
|
spi_software_mosi_pin: nhk:gpio20
|
|
spi_software_miso_pin: nhk:gpio19
|
|
|
|
[resonance_tester]
|
|
accel_chip: adxl345
|
|
accel_per_hz: 100
|
|
sweeping_accel: 400
|
|
sweeping_period: 0
|
|
##--------------------------------------------------------------------
|
|
## Uncomment below for 250mm build
|
|
#probe_points:
|
|
# 125, 125, 20
|
|
|
|
## Uncomment below for 300mm build
|
|
#probe_points:
|
|
# 155, 155, 20
|
|
|
|
## Uncomment below for 350mm build
|
|
#probe_points:
|
|
# 175, 175, 20
|
|
|
|
##--------------------------------------------------------------------
|
|
|
|
#####################################################################
|
|
# Thermistors
|
|
# #####################################################################
|
|
## External Chamber Thermistor Port
|
|
[temperature_sensor chamber_temp]
|
|
sensor_type: Generic 3950
|
|
sensor_pin: nhk:gpio28
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: chamber_th
|
|
|
|
[thermistor CMFB103F3950FANT]
|
|
temperature1: 0.0
|
|
resistance1: 32116.0
|
|
temperature2: 40.0
|
|
resistance2: 5309.0
|
|
temperature3: 80.0
|
|
resistance3: 1228.0
|
|
|
|
[temperature_sensor nh_temp]
|
|
## Nitehawk PCB Sensor
|
|
sensor_type: CMFB103F3950FANT
|
|
sensor_pin: nhk:gpio26
|
|
pullup_resistor: 2200
|
|
min_temp: 0
|
|
max_temp: 100
|
|
gcode_id: nh_th
|
|
|